Restaurant exhaust hood types: Type I, Type II and Korean BBQ hoods

Restaurant exhaust hoods come in two code classes and several physical styles. A Type I hood collects grease vapors and smoke and has a fire suppression system. A Type II hood handles steam, heat, odors and combustion products from appliances that make no grease or smoke. The styles include wall canopy, single and double island, backshelf (proximity), pass-over and eyebrow hoods. Hoods are either listed factory-built units or field-built to code. Korean BBQ table hoods and downdraft grills sit outside the usual kitchen line, so your designer and local reviewer must decide which code path applies to them.
This guide explains the hood classes and styles. For choosing a Korean BBQ ventilation system and working out make-up air, see the Korean BBQ ventilation guide.
Type I and Type II hoods
The International Mechanical Code (IMC) defines the two classes. The 2024 IMC definitions, as adopted in Chicago, read:
- Type I: "A kitchen hood for collecting and removing grease vapors and smoke. Such hoods are equipped with a fire suppression system."
- Type II: "A general kitchen hood for collecting and removing steam, vapor, heat, odors and combustion products."
Section 507.1 of the 2021 IMC, quoted in a Utah mechanical code discussion, adds two rules. Where any appliance under a single hood needs a Type I hood, the hood must be Type I. Where a Type I hood is installed, the whole system must comply: the hood, ducts, exhaust equipment and make-up air.
The 2024 IMC moved the Type II rule to section 507.3, according to a Montana Department of Labor and Industry training handout. Type II hoods go over light-duty cooking appliances, dishwashers and appliances that produce heat, moisture or combustion products but no grease or smoke.
Is a residential range hood allowed in a restaurant?
Check your local rule first. The Cartersville, Georgia fire department checklist limits residential hoods to residential cooking equipment with no more than four burners, used for food warming, limited cooking, rehabilitation training or home economics classrooms. It does not allow them in assembly occupancies, except churches. A grill table in a dining room does not fit those limits.
Hood styles
The New York City Mechanical Code defines the common styles:
- Wall canopy: mounted against a wall above an appliance line. The wall acts as a back panel and draws make-up air across the front of the cooking equipment.
- Single island canopy: over one appliance line, open on all sides. The code notes it is more sensitive to cross drafts and needs more exhaust air than an equal wall canopy.
- Double island canopy: over back-to-back appliance lines, open on all sides.
- Backshelf: also called a low-proximity hood. Its front lip sits low over the appliances and is set back from their front edge.
- Pass-over: a free-standing backshelf hood that is low enough to pass food over the top.
- Eyebrow: mounted to the face of an appliance, such as an oven or dishwasher, above the door.
Manufacturers use the same names. CaptiveAire describes island hoods for cooking equipment where no walls exist, including display cooking. The Greenheck hood catalog says its proximity hoods sit close to the cooking equipment and suit light and medium-duty cooking with low ceilings.
Listed hoods and field-built hoods
Listed hoods (UL 710)
UL 710 covers Type I commercial kitchen exhaust hoods placed over commercial cooking equipment. Its scope says hoods are evaluated for the minimum exhaust airflow and maximum supply airflow needed to capture and contain cooking effluent under laboratory conditions. It does not cover fire-extinguishing systems or grease extraction efficiency. Recirculating systems fall under a separate standard, UL 710B.
An ICC training handout lists the IMC 507.1 exceptions for UL 710 listed factory-built hoods. It also notes that listed Type I hoods carry a label with the exhaust flow for each appliance duty class. Ask the hood maker for the listing and the installation instructions for your model.
Field-built hoods
An unlisted hood is built to the code's construction rules. The ICC handout lists No. 18 gage steel or No. 20 gage stainless steel as Type I hood materials, and grease filters listed to UL 1046.
Other code paths
The Port of San Francisco hood procedure, based on the 2025 California Mechanical Code, lists other ways to meet a Type I requirement. Two of them matter here:
- Recirculating systems listed to UL 710B.
- Listed and labeled cooking appliances with integral downdraft systems that comply with CMC section 518.0.
Each exception needs a listing for the exact equipment. A product description alone does not meet it.

Where Korean BBQ table hoods fit
The code texts cited here do not name Korean BBQ table hoods. A table grill that produces grease and smoke raises the Type I question, so the hood above it needs a defined code path.
Ask your designer and the local reviewer which path they will accept:
- A table hood treated as a listed Type I hood, with a listing for that model.
- A field-built Type I design, with the code's construction, filter and duct rules.
- A listed downdraft appliance in place of an overhead hood.
Overhead table hoods
The Korean BBQ Exhaust Hood Type A listing describes an ETL certified hood with a UL certified grease filter. It also describes a slanted stainless steel filter that drains into a removable grease collector. Ask which standard the hood certification covers, such as UL 710, and check the model in the certifier's directory. The equipment certification guide explains how to read those documents.
The Korean BBQ Exhaust Hood Type B listing describes a retractable SUS304 stainless steel hood that extends from 52.8 inches to 67.3 inches, with a 150 ml grease collector. Ask for its listing documents before you plan it as a Type I hood.
Downdraft grills
The DB-2017G Smokeless Down-Draft Hood listing describes a downdraft system that pulls smoke down at the table, with a 4-stage filter system. The listing says the system includes the DB-2017G roaster, the SC-9700 hood box table stand and a C-BOX control unit. Ask whether the roaster and its exhaust are listed and labeled together for this use, as the downdraft exception requires. The downdraft retrofit survey lists the site checks for an existing building.
Questions to ask before you choose a hood type
- Which mechanical code and edition does the local authority enforce?
- Does the reviewer treat each grill table as needing a Type I hood?
- Is the proposed hood listed, and to which standard?
- If it is field-built, who designs the construction, filters and exhaust rates?
- For a downdraft grill, is the appliance and its exhaust listed together?
- Which fire suppression system covers each table hood?
Next step
Compare current Korean BBQ exhaust hoods, then send your layout, table count and grill fuel through Get a Quote. Your mechanical designer and local reviewer set the final hood type and exhaust design.



